Tungsten was designed as an armour material for the first wall of magnetic confinement thermonuclear fusion devices. Furthermore, due to its low permeation-retention properties is a candidate for use as barrier layer to the diffusion of tritium. Therefore it is necessary to identify an industrial scalable manufacturing method for W coatings with a thickness in the µm range on carbon based substrates. As reported in literature [1], direct deposition of W on Carbon Fibre Composite (CFC) was troublesome because of the poor adhesion: an intermediate molybdenum layer can solve the problem. The beneficial role of Mo seems to be in connection with the adjustment of the thermal expansion mismatch between CFC and W. We are performing an investigation on the properties of Mo, W and Mo/W coatings deposited by DC magnetron sputtering. The Mo films have been deposited on different substrates and they have been analyzed using scanning electron microscopy and X-r ay diffraction to verify their morphologies and grain structures. The W coatings have been grown on glass, graphite, Si, Si/Mo, Ti and Ti/Mo changing progressively the sputtering parameters to optimize the process. The thermodynamically stable form of metallic tungsten is body-centered-cubic (?-W) but sputter-deposited tungsten thin films with an A15 metastable structure (?-W) have been commonly observed [2]. The tungsten coating final phase depends on substrate bias and temperature, deposition pressure, residual gas species (as an example O2 and N2 absorbed in the films promote the formation of ?-W). The goal of this work is to find a correlation between W properties and a variety of deposition parameters. The XRD spectra show the ?-W equilibrium phase dominates when a dc bias voltage is applied to the substrate. Moreover a series of SEM micrographs reveals that employing a DC bias it is possible to improve the surface morphology and compactness of the film. Bacause the wear and the adhesion are foundametal properties of hard coatings in view of tribological-mechanical demands, scratch and tribological tests were performed using a fully-computerized UMT tester. Hardness measurements were performed by the nano-indentation technique. The base pressure was reduced as much as possible (< level of impurities), the deposition temperature was increased or a post-annealing of the coatings was introduced. The substrate movement effect and the target-substrate distance role have been studied. The possible use of different alloys is under investigation too.
Mo, W and Mo/W Films by DC Magnetron Sputtering
2010
Abstract
Tungsten was designed as an armour material for the first wall of magnetic confinement thermonuclear fusion devices. Furthermore, due to its low permeation-retention properties is a candidate for use as barrier layer to the diffusion of tritium. Therefore it is necessary to identify an industrial scalable manufacturing method for W coatings with a thickness in the µm range on carbon based substrates. As reported in literature [1], direct deposition of W on Carbon Fibre Composite (CFC) was troublesome because of the poor adhesion: an intermediate molybdenum layer can solve the problem. The beneficial role of Mo seems to be in connection with the adjustment of the thermal expansion mismatch between CFC and W. We are performing an investigation on the properties of Mo, W and Mo/W coatings deposited by DC magnetron sputtering. The Mo films have been deposited on different substrates and they have been analyzed using scanning electron microscopy and X-r ay diffraction to verify their morphologies and grain structures. The W coatings have been grown on glass, graphite, Si, Si/Mo, Ti and Ti/Mo changing progressively the sputtering parameters to optimize the process. The thermodynamically stable form of metallic tungsten is body-centered-cubic (?-W) but sputter-deposited tungsten thin films with an A15 metastable structure (?-W) have been commonly observed [2]. The tungsten coating final phase depends on substrate bias and temperature, deposition pressure, residual gas species (as an example O2 and N2 absorbed in the films promote the formation of ?-W). The goal of this work is to find a correlation between W properties and a variety of deposition parameters. The XRD spectra show the ?-W equilibrium phase dominates when a dc bias voltage is applied to the substrate. Moreover a series of SEM micrographs reveals that employing a DC bias it is possible to improve the surface morphology and compactness of the film. Bacause the wear and the adhesion are foundametal properties of hard coatings in view of tribological-mechanical demands, scratch and tribological tests were performed using a fully-computerized UMT tester. Hardness measurements were performed by the nano-indentation technique. The base pressure was reduced as much as possible (< level of impurities), the deposition temperature was increased or a post-annealing of the coatings was introduced. The substrate movement effect and the target-substrate distance role have been studied. The possible use of different alloys is under investigation too.I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.
